DR1-B
The motorcycle dyno equipped with a 1200Nm eddy current brake and an ultra-fast brake interface is ready for the most demanding tuners. DR1-B offers many testing capabilities, such as: inertial runs, ramp test, steady-state or user defined custom load profiles. The advance data logger (offered as standard with each of our dyno) and a wide range of accessories help to maximize any vehicle’s performance.
€12 500
SPECIFICATION
DR1-B | |
Type | motorcycle, braked |
Dimensions LxW [mm] | 2400 x 1500/400 |
Roller type | knurled, chromium plated |
Roller diameter [mm] | 402 |
Rollers balancing class | G2,5 |
Roller linkage | n/a |
Max/Min track [mm] | n/a |
Min wheel diameter [mm] | n/a |
Max weight per axle [kg] | 1000 |
Max/Min wheelbase [mm] | 2300 / 1120 |
Mechanical axles linkage system | n/a |
Eddy current brake [Nm] | yes, 1200 |
Max tractive force [N] | 5970 |
Vmax [km/h] | 330 |
Max measurement error [%] | 0,1 |
Power requirements | 110-400VAC; 50-60Hz; 1-3 ph |
Installation variants | above ground / portable |
GENERAL: | |
Power supply | 100-240 VAC, 50-60Hz, 1.5A, IEC C14 socket |
Dimensions LxWxH [mm] | 250x120x45 |
Mass | 620g |
Computer specification | 4-core Cortex A72 1,5GHz, RAM 8GB, Data memory 256GB |
Microcontroller specification | 32-bit RISC 64MHz |
Ports: | 2x USB 2.0, 2x USB 3.0, 2x micro HDMI, 1x Audio mini jack, 1x Gigabit Ethernet |
Communication: | Ethernet, Bluetooth 5.0, WiFi IEEE 802.11b/g/n/ac (2,4/5 GHz) |
DATA LOGGING: | |
Weather station | temperature, pressure, humidity |
CAN-BUS 2.0B | 2x (compatible with ISO-11898-2 and ISO-11898-5) |
Analog inputs | 6x (0-5V) |
Thermocouple / High precision analog inputs | 8x |
Physical switch inputs | 4x |
Power outputs | 3x (24V, 12V, 5V(2A) with total capacity of 20W) |
Free frequency input | 1x (15kHz) |
Analog outputs | 2x (0-10V) |
Low side PWM outputs | 4x (40V, 3A) |
Relay outputs | 4x (250V, 16A ) |
Test modes | sweep test (inertial), sweep test (ramp – constant acceleration), steady-state mode, manual mode with programmable profiles |
DR2-I
The base model offered by Dyno Revolt allows for precise measurement of power and torque in inertial mode. This chassis dyno is known for its accurate results, affordable price point, and the ability to grow with your shop. It’s a great choice for novice tuners or just for progress testing. The dyno is equipped with an advance data logger and it’s ready for further upgrade with an eddy current brake or extension to AWD version.
€12 900
SPECIFICATION
DR2-I | |
Type | 2WD, inertial |
Dimensions LxW [mm] | 900×2720 |
Roller type | knurled, chromium plated |
Roller diameter [mm] | 320 |
Rollers balancing class | G2,5 |
Roller linkage | yes, by shafts and high performance synchronous belts |
Max/Min track [mm] | 2240/900 |
Min wheel diameter [mm] | 200 |
Max weight per axle [kg] | 3000 |
Max/Min wheelbase [mm] | n/a |
Mechanical axles linkage system | n/a |
Eddy current brake | upgradeable |
Vmax [km/h] | 300 |
Max measurement error [%] | 0,1 |
Power requirements | 230V |
Installation variants | in-pit / above ground / portable |
GENERAL: | |
Power supply | 100-240 VAC, 50-60Hz, 1.5A, IEC C14 socket |
Dimensions LxWxH [mm] | 250x120x45 |
Mass | 620g |
Computer specification | 4-core Cortex A72 1,5GHz, RAM 8GB, Data memory 256GB |
Microcontroller specification | 32-bit RISC 64MHz |
Ports: | 2x USB 2.0, 2x USB 3.0, 2x micro HDMI, 1x Audio mini jack, 1x Gigabit Ethernet |
Communication: | Ethernet, Bluetooth 5.0, WiFi IEEE 802.11b/g/n/ac (2,4/5 GHz) |
DATA LOGGING: | |
Weather station | temperature, pressure, humidity |
CAN-BUS 2.0B | 2x (compatible with ISO-11898-2 and ISO-11898-5) |
Analog inputs | 6x (0-5V) |
Thermocouple / High precision analog inputs | 8x |
Physical switch inputs | 4x |
Power outputs | 3x (24V, 12V, 5V(2A) with total capacity of 20W) |
Free frequency input | 1x (15kHz) |
Analog outputs | 2x (0-10V) |
Low side PWM outputs | 4x (40V, 3A) |
Relay outputs | 4x (250V, 16A ) |
Test modes | sweep test (inertial) |
DR2-B
The single axle dyno equipped with a 2000Nm eddy current brake is ready for the most demanding tuners. DR2-B offers many testing capabilities, such as: inertial runs, ramp test, steady-state or user defined custom load profiles. The advance data logger (offered as standard with each of our dyno) and a wide range of accessories help to maximize any vehicle’s performance. Similar like the DR2-I, this dyno also is ready for further extension to AWD version.
€19 800
SPECIFICATION
DR2-B | |
Type | 2WD, braked |
Dimensions LxW [mm] | 900×3250 |
Roller type | knurled, chromium plated |
Roller diameter [mm] | 320 |
Rollers balancing class | G2,5 |
Roller linkage | yes, by shafts and high performance synchronous belts |
Max/Min track [mm] | 2240/900 |
Min wheel diameter [mm] | 200 |
Max weight per axle [kg] | 3000 |
Max/Min wheelbase [mm] | n/a |
Mechanical axles linkage system | n/a |
Eddy current brake [Nm] | yes, 1×2000 |
Max tractive force [N] | 12500 |
Vmax [km/h] | 300 |
Max measurement error [%] | 0,1 |
Power requirements | 230V, 16A or 400V, 10A |
Installation variants | in-pit / above ground / portable |
GENERAL: | |
Power supply | 100-240 VAC, 50-60Hz, 1.5A, IEC C14 socket |
Dimensions LxWxH [mm] | 250x120x45 |
Mass | 620g |
Computer specification | 4-core Cortex A72 1,5GHz, RAM 8GB, Data memory 256GB |
Microcontroller specification | 32-bit RISC 64MHz |
Ports: | 2x USB 2.0, 2x USB 3.0, 2x micro HDMI, 1x Audio mini jack, 1x Gigabit Ethernet |
Communication: | Ethernet, Bluetooth 5.0, WiFi IEEE 802.11b/g/n/ac (2,4/5 GHz) |
DATA LOGGING: | |
Weather station | temperature, pressure, humidity |
CAN-BUS 2.0B | 2x (compatible with ISO-11898-2 and ISO-11898-5) |
Analog inputs | 6x (0-5V) |
Thermocouple / High precision analog inputs | 8x |
Physical switch inputs | 4x |
Power outputs | 3x (24V, 12V, 5V(2A) with total capacity of 20W) |
Free frequency input | 1x (15kHz) |
Analog outputs | 2x (0-10V) |
Low side PWM outputs | 4x (40V, 3A) |
Relay outputs | 4x (250V, 16A ) |
Test modes | sweep test (inertial), sweep test (ramp – constant acceleration), steady-state mode, manual mode with programmable profiles |
DR4-I
The inertia AWD chassis dynamometer with fully linked axles enables accurate testing of all the newest cars (both 2WD and AWD) equipped with an advanced traction and torque management control system. The appropriate moment of inertia of the whole set of rollers allows correct measurement of most street cars. Similar like the DR2-I, also the DR4-I dyno can be easily upgraded with eddy current brakes to meet the highest demands.
€39 900
SPECIFICATION
DR4-I | |
Type | AWD, inertial, linked |
Dimensions LxW [mm] | 4045×2720 |
Roller type | knurled, chromium plated |
Roller diameter [mm] | 320 |
Rollers balancing class | G2,5 |
Roller linkage | yes, by shafts and high performance synchronous belts |
Max/Min track [mm] | 2240/900 |
Min wheel diameter [mm] | 200 |
Max weight per axle [kg] | 3000 |
Max/Min wheelbase [mm] | standard: 2990/2300 (nominal); 3150/2150 (total) extended: 3310/2300 (nominal); 3470/2150 (total) |
Mechanical axles linkage system | yes, by high performance synchronous belt |
Eddy current brake | upgradeable |
Vmax [km/h] | 300 |
Max measurement error [%] | 0,1 |
Power requirements | 230V |
Installation variants | in-pit / above ground |
GENERAL: | |
Power supply | 100-240 VAC, 50-60Hz, 1.5A, IEC C14 socket |
Dimensions LxWxH [mm] | 250x120x45 |
Mass | 620g |
Computer specification | 4-core Cortex A72 1,5GHz, RAM 8GB, Data memory 256GB |
Microcontroller specification | 32-bit RISC 64MHz |
Ports: | 2x USB 2.0, 2x USB 3.0, 2x micro HDMI, 1x Audio mini jack, 1x Gigabit Ethernet |
Communication: | Ethernet, Bluetooth 5.0, WiFi IEEE 802.11b/g/n/ac (2,4/5 GHz) |
DATA LOGGING: | |
Weather station | temperature, pressure, humidity |
CAN-BUS 2.0B | 2x (compatible with ISO-11898-2 and ISO-11898-5) |
Analog inputs | 6x (0-5V) |
Thermocouple / High precision analog inputs | 8x |
Physical switch inputs | 4x |
Power outputs | 3x (24V, 12V, 5V(2A) with total capacity of 20W) |
Free frequency input | 1x (15kHz) |
Analog outputs | 2x (0-10V) |
Low side PWM outputs | 4x (40V, 3A) |
Relay outputs | 4x (250V, 16A ) |
Test modes | sweep test (inertial) |
DR4-B
The first of two AWD braked dynamometers in our offer. DR4-B is equipped with one eddy current brake which may generate an extra load (up to 2000Nm) during runs of the most powerful cars. The axle linking system guarantee the proper torque distribution between each rollers and the same speed of every car’s wheel. This model can be upgraded later with a second brake for the highest performance and operational capabilities.
€46 900
SPECIFICATION
DR4-B | |
Type | AWD, braked, linked |
Dimensions LxW [mm] | 4045×3250 |
Roller type | knurled, chromium plated |
Roller diameter [mm] | 320 |
Rollers balancing class | G2,5 |
Roller linkage | yes, by shafts and high performance synchronous belts |
Max/Min track [mm] | 2240/900 |
Min wheel diameter [mm] | 200 |
Max weight per axle [kg] | 3000 |
Max/Min wheelbase [mm] | standard: 2990/2300 (nominal); 3150/2150 (total) extended: 3310/2300 (nominal); 3470/2150 (total) |
Mechanical axles linkage system | yes, by high performance synchronous belt |
Eddy current brake [Nm] | yes, 1×2000 |
Max tractive force [N] | 12500 |
Vmax [km/h] | 300 |
Max measurement error [%] | 0,1 |
Power requirements | 230V, 16A or 400V, 10A |
Installation variants | in-pit / above ground |
GENERAL: | |
Power supply | 100-240 VAC, 50-60Hz, 1.5A, IEC C14 socket |
Dimensions LxWxH [mm] | 250x120x45 |
Mass | 620g |
Computer specification | 4-core Cortex A72 1,5GHz, RAM 8GB, Data memory 256GB |
Microcontroller specification | 32-bit RISC 64MHz |
Ports: | 2x USB 2.0, 2x USB 3.0, 2x micro HDMI, 1x Audio mini jack, 1x Gigabit Ethernet |
Communication: | Ethernet, Bluetooth 5.0, WiFi IEEE 802.11b/g/n/ac (2,4/5 GHz) |
DATA LOGGING: | |
Weather station | temperature, pressure, humidity |
CAN-BUS 2.0B | 2x (compatible with ISO-11898-2 and ISO-11898-5) |
Analog inputs | 6x (0-5V) |
Thermocouple / High precision analog inputs | 8x |
Physical switch inputs | 4x |
Power outputs | 3x (24V, 12V, 5V(2A) with total capacity of 20W) |
Free frequency input | 1x (15kHz) |
Analog outputs | 2x (0-10V) |
Low side PWM outputs | 4x (40V, 3A) |
Relay outputs | 4x (250V, 16A ) |
Test modes | sweep test (inertial), sweep test (ramp – constant acceleration), steady-state mode, manual mode with programmable profiles |
DR4-B2
Our top-of-the-range dyno equipped with 2 eddy current brakes and fully linked axles is dedicated to the most demanding customers. The 4000Nm of braking torque controlled by innovate and ultra-fast brake interface guarantee the proper load of even the most powerful cars and accurate testing that gives precise and repeatable data run after run.
€53 800
SPECIFICATION
DR4-2B | |
Type | AWD, braked, linked |
Dimensions LxW [mm] | 4045×3250 |
Roller type | knurled, chromium plated |
Roller diameter [mm] | 320 |
Rollers balancing class | G2,5 |
Roller linkage | yes, by shafts and high performance synchronous belts |
Max/Min track [mm] | 2240/900 |
Min wheel diameter [mm] | 200 |
Max weight per axle [kg] | 3000 |
Max/Min wheelbase [mm] | standard: 2990/2300 (nominal); 3150/2150 (total) extended: 3310/2300 (nominal); 3470/2150 (total) |
Mechanical axles linkage system | yes, by high performance synchronous belt |
Eddy current brake [Nm] | yes, 2×2000 |
Max tractive force [N] | 25000 |
Vmax [km/h] | 300 |
Max measurement error [%] | 0,1 |
Power requirements | 230V, 32A or 400V, 20A |
Installation variants | in-pit / above ground |
GENERAL: | |
Power supply | 100-240 VAC, 50-60Hz, 1.5A, IEC C14 socket |
Dimensions LxWxH [mm] | 250x120x45 |
Mass | 620g |
Computer specification | 4-core Cortex A72 1,5GHz, RAM 8GB, Data memory 256GB |
Microcontroller specification | 32-bit RISC 64MHz |
Ports: | 2x USB 2.0, 2x USB 3.0, 2x micro HDMI, 1x Audio mini jack, 1x Gigabit Ethernet |
Communication: | Ethernet, Bluetooth 5.0, WiFi IEEE 802.11b/g/n/ac (2,4/5 GHz) |
DATA LOGGING: | |
Weather station | temperature, pressure, humidity |
CAN-BUS 2.0B | 2x (compatible with ISO-11898-2 and ISO-11898-5) |
Analog inputs | 6x (0-5V) |
Thermocouple / High precision analog inputs | 8x |
Physical switch inputs | 4x |
Power outputs | 3x (24V, 12V, 5V(2A) with total capacity of 20W) |
Free frequency input | 1x (15kHz) |
Analog outputs | 2x (0-10V) |
Low side PWM outputs | 4x (40V, 3A) |
Relay outputs | 4x (250V, 16A ) |
Test modes | sweep test (inertial), sweep test (ramp – constant acceleration), steady-state mode, manual mode with programmable profiles |